A soft two part thixotropic epoxy mortar/paste, gunable and trowellable. EPAR HPN has excellent adhesion to most materials including concrete, metals, bricks, ceramic, glass etc. EPAR HPN is non shrink and has excellent chemical resistance. Also available with a cold cure hardener for use from 0°C - 10°C

USES
The excellent mechanical properties of EPAR HPN make it suitable for many applications including the following:

• Bedding and jointing of precast concrete units.
• Grouting of horizontal starter bars and bolts.
• Repair of spalling concrete and protection of reinforcing.
• Levelling and patching of concrete floors under heavy load or impact.
• Fabrication of concrete pipe intersections.
• Tiling.
• Bonding of aggregates to concrete etc., for decorative finishes.
• Bedding of machines and backing plates both vertical and horizontal.

‍

Epar S is a low-viscosity epoxy resin system designed for high-strength grouting, void filling, and structural bonding applications.  Epar S non shrink with excellent chemical resistance. also avaliable in 'cold-cure' formulation.

Key Points

• 2 part pourable Epoxy Grout
• Ideal for machinery base plates and crane rails
• Effective and economical forstarter bars or holding down bolts in concrete
• Suitable for Industrial floor repairs

ER-921 is a surface-active agent used to reduce the water evaporation rate from the surface of newly laid concrete. It is designed to form a thin film to reduce rapid moisture loss from the concrete surface. ER-921 is spray applied in diluted form to fresh concrete flatwork to reduce the tendency for surface plastic cracking to occur. ER-921 aids and improves the workability and finishing characteristics of the concrete surface. ER-921 also helps extend the surface workability time for a given set of weather conditions.

USES

• Use ER-921 as an evaporation retarder for concrete flatwork surfaces when the evaporation rate exceeds the bleeding rate. Recommended for use on all concrete surfaces except dry shake hardeners and toppings.

‍

Deep Etch, spray applied concrete surface retarder for concrete cold joints.

Key Points

• Spray-applied deep etch retarder
• Controls surface set for exposed aggregate
• Suitable for cold joint preparation
• Simple application for site use

Paint on Vertical Surface Retarder. Applied to formwork to facilitate easy removal of the concrete slurry once stripped. Leaves a profiled surface for horizontal cold joints.

Key Points

• Paint-on vertical surface retarder
• Enables slurry removal after form stripping
• Produces profiled surface for cold joints
• Suitable for vertical concrete applications

For all applications.

Ezee CSR+ is sprayed or rolled onto the concrete surface to delay the surface set, making wash-off easier and producing a uniform decorative or construction joint finish. Designed for deep etch construction joints exposing aggregate to a depth of over 5mm.

Key Points

• High-performance surface retarder
• Produces clean, consistent aggregate exposure
• Formulated for >35Mpa Construction Joints
• Suitable for insitu and precast concrete
• 3.5-

Developed primarily as a curing compound for concrete, as well as resolve compatibility issues related to flooring adhesives. E-Cure is a spray applied concrete cure, hardener and dustproofer. It penetrates and forms a temporary membrane to cure, densify, harden and dustproof concrete essential for proper strength development. E-Cure meets the moisture retention of ASTM C-309 on hard-troweled concrete surfaces.

Key Points

• Cures, hardens, and dustproofs concrete
• Spray-applied penetrating formulation
• Improves compatibility with flooring adhesives
• Meets ASTM C-309 and NZS3109 standards
• Ultralow PH.

Formoil DF is our 'go-to' form release agent we recommend for most precast and general concrete applications.

Diesel-free and designed for New Zealand’s varying weather conditions, Formoil DF delivers clean, reliable concrete release from a variety of formwork. It reduces staining, limits residue buildup and cuts down the time spent cleaning forms after stripping.

For contractors and precast yards wanting dependable performance without the hazards of diesel alternatives, Formoil DF is the release agent we trust first.

Key Points

• Diesel-free formulation
• Consistent, clean, reliable release.
• Minimal residual build-up and clean-up time
• Reliable for precast and general concrete applications
• Coverage >20m2 P/lt on Timber and Plywood, >30m2 P/lt Steel, Formply, aluminum.

• Quick Dry Formulation
• Strong and Bright Colours
• Spray-through cap reduces finger contamination
• No Tolulene or MEK
• Worksafe compliant colours

‍

Deep etch paint on retarder for application to concrete formwork.  A quick-set water carried hybrid formulation, facilitating up to 10mm concrete retardation and exposing aggregate for structural cold joints.

Key Points

• Deep-etch paint-on surface retarder
• Allows up to 10mm concrete retardation
• Supports structural cold joint preparation
• Quick-set water-carried hybrid formulation

Ezi-action Drumpumps are the best hand drum pump in the world. They are the most dependable manual dispensing system for bulk containers.

The Ezi-action Drumpump has been designed with user safety in mind. They make a workplace safer and more efficient.

Ezi-action Drum Pumps are Easy to Use:

• Two fingers on the ergonomically designed ball handle is all the energy required for hand pumping and fluid transfer.
• Pumps viscous fluids up to 8,800 cps including oils, lubricants, molasses, and moisturisers.
• Easy performance throughout the lifetime of this totally plastic pump.

Ezi-action Drum Pumps are Reliable and Economical:

• Revolutionary, patented double action pumping principle.
• No critical wearing parts to wear or break.
• Fast, continuous flow. high volume, low pressure.
• Reaches to the base of drum or container and empties all the contents.
• Prevents waste with swivel spout and no leaking.
• 24 month manufacturer's warranty.
• Manufactured in New Zealand and USA.

Ezi-action Drum Pumps are Fully Serviceable:

• Only fully serviceable hand pump in the world.
• Provides years of reliable dispensing.

Ezi-action Drum Pumps are Customisable:

• Can be fitted with a coloured safety strap.
• Avoid chemical mix-ups.
• Differentiate to acid or alkali chemicals.

Ezi-action Drum Pumps have:

• Excellent Chemical Compatibility and are Food Safe.
• Effective Safety Features.
• Controllable Siphon Action.

‍

Approved screw head filler for Hardie and Titan Fibre Cement Sheets

A two part, light and sandable epoxy fairing and filling compound. FAIRFILL is non-shrinking, nonporous and cold curing thereby allowing application in all temperatures. FAIRFILL is easily sanded using a power sander or other woodworking/finishing tools.

Range of sizes.

Key Points

• High-build shrinkage-compensated repair mortar
• Suitable for vertical and overhead repairs
• Low permeability for durability
• Ideal for large structural reinstatement works

Fosroc Renderoc HB40 Plus is a high-build, shrinkage-compensated repair mortar for reinstating damaged reinforced concrete.
It is designed for vertical and overhead concrete repairs where strength, durability, and build thickness matter. HB40 Plus is suitable for patch repairs to walls, beams, columns, soffits, precast panels, car parks, civil structures, and other areas where damaged or spalled concrete needs to be rebuilt with confidence.
The high-build formulation allows larger repairs to be completed with fewer applications, while the shrinkage-compensated design helps maintain dimensional stability as the repair cures. HB40 Plus also offers low permeability to water, carbon dioxide, and chloride ions, making it a strong option for exposed or aggressive environments where long-term durability is important.

‍

‍

A resin-based curing compound designed to provide efficient moisture retention and surface protection during concrete curing. It helps improve concrete strength development by reducing premature drying. Reduces shrinkage cracking. Fracure is suitable for commercial and industrial concrete applications.

Key Points

• Resin/Hydrocarbon curing compound
• Forms thin skin of resin
• Traps moisture in the concrete slab
• Reduces premature drying and cracking
• 7㎡ P/lt

Fracure Emulsion is a synthetic water based emulsion.

When applied to newly poured concrete Fracure Emulsion quickly dries to form a tough long lasting wear resistant film with low water vapour permeability.

By reducing evaporation from the concrete surface, the water necessary for cement hydration is maintained. This allows the maximum development of compressive and tensile strength in the finished concrete and results in a more durable surface with lower permeability.

USES

• Fracure Emulsion is suitable for use on all concrete surfaces made from Portland and other hydraulic type cements. All exposed elements of a structure subject to water loss due to evaporation should be cured. These include floor slabs, columns, beams, walls, precast panels etc.
• FRracure Emulsion is compatible with most plaster and paint finishing systems and having good U.V. and alkali resistance, will remain sound during construction until such finishes are applied.
• Being non-toxic Fracure Emulsion is suitable for use on potable water retaining structures.
• Made need to be mechanically removed prior to subsequent coatings

‍

Description:

Fracure Wax Emulsion is a water-based wax emulsion concrete curing compound, designed to maximise concrete strength and durability by forming an impermeable membrane that significantly reduces moisture loss during the curing process. It is typically applied to freshly placed concrete to ensure proper cement hydration, helping reduce shrinkage, dusting, and surface cracking while improving overall wear resistance.
It is suitable for exterior concrete surfaces where no subsequent coatings or treatments are planned, and it is considered a high-performance curing option where maximum moisture retention is required.

Key Points

• Water-based wax emulsion system preapproved for most airport authorities.
• Forms impermeable moisture barrier at 3.5-5m2 P/lt
• Reduces shrinkage and dusting
• Maximises strength and durability
• Exceeds ASTM C-309/NZS3109

Geocross is a paving grid made of regenerated plastic for lightning-fast set up of surfaces for vehicle access and airfields. It guarantees stabilisation and support to existing grass surfaces and is installed by a simple laying and rolling of the grid into the ground. To ensure optimal performance it must be completely embedded into the ground. The embossed surface provides an excellent wheel grip. When Geocross is well rolled in the ground it creates a surface that allows great stability and excellent rainwater permeability over time.

Key Points

• Recycled plastic ground stabilisation grid
• Designed for vehicle access and airfields
• Improves load support and surface stability
• Enhances grass reinforcement and drainage

Geopanel Star is a modular formwork system designed for flexible and efficient concrete forming in walls and structural elements. It offers quick assembly, reusable components, and consistent high-quality concrete finishes. Geopanel Star is ideal for projects requiring adaptability to different shapes and layouts while maintaining speed of installation.

Key Points

• Flexible modular formwork system
• Quick assembly with reusable components
• Suitable for varied shapes and layouts
• Consistent high-quality concrete finish

Geopanel Wall is a modular, lightweight formwork system designed for fast and efficient casting of concrete walls. It uses reusable panels that provide accurate alignment, smooth concrete finishes, and reduced labour requirements on site. Geopanel Wall is suitable for residential, commercial, and civil wall construction where speed and precision are important.

Key Points

• Modular lightweight wall formwork system
• Reusable panels for fast assembly
• Produces smooth, accurate concrete finishes
• Reduces labour and installation time

GEOTUB is the first formwork in technopolymer for the construction of round and oval columns. It is a complete system for the production of columns, both for residential and industrial use.

Manufacturers claim of up to 100 reuses means they are easily the smart option against steel or cardboard. Lightweight and modular means they can be erected by one person and with no crane time required.

GEOTUB's smooth surface facilitates easy stripping and a provides a smooth clean concrete finish with a minimum of imperfections.

‍

Advantages:
‍

• Light: Weighing max 10 kg, GEOTUB can be handled quickly on site without having to use cranes or other mechanical lifting devices.
  ‍
• Fast: Light and easy to assemble, it can be installed and handled by a single person.
  ‍
• Modular: All elements are 600 mm long and only the elements necessary for the pour are used.
  ‍
• Water resistant: Ideal for marine solutions.
  ‍
• Versatile: Combine with GEOPANEL to produce oval columns - an ideal solution for car parks.
  ‍
• Reusable: GEOTUB is cost effective as it can be reused more than 100 times when properly used and maintained.
  ‍
• Dismantling: Concrete does not stick to plastic so dismantling is extremely easy.
  ‍
• Storage: GEOTUB can be safely and conveniently stored even in damp places.

GEOTUB PANEL is a formwork system in technopolymer for the construction of square and rectangular columns, both for residential and industrial use.

Lightweight and modular means they can be easily erected and with no crane time required.

The particularly smooth internal surface of GEOTUB PANEL facilitates easy stripping and a provides a smooth clean concrete finish with a minimum of imperfections.

‍

Advantages:
‍

• Light: Weighing max 10 kg, GEOTUB PANEL can be handled quickly on site without having to use cranes or other mechanical lifting devices.
  ‍
• Fast: Light and easy to assemble, it can be installed and handled by a single person.
  ‍
• Modular: All elements are 750 mm long and only the elements necessary for the pour are used.
  ‍
• Water resistant: Ideal for marine solutions.
  ‍
• Versatile: Combine panels to produce 55 different square and rectangular column sizes.
  ‍
• Reusable: GEOTUB PANEL is cost effective as it can be reused more than 100 times when properly used and mantained.
  ‍
• Dismantling: Concrete does not stick to plastic so dismantling is extremely easy.
  ‍
• Storage: GEOTUB PANEL can be completely dismantled and stored even in damp places.

Hand protection is an essential part of workplace safety, helping protect against everyday handling risks as well as more demanding, task specific hazards.

Self adhesive foam to prevent grout loss from formwork.

6mm x 12mm

12mm x 18mm